Skylla-i remote on-off cable
This cable is intended for on/off control of the Skylla-i when the source signal is high when the Skylla-i must be on, and low or free floating when Skylla-i must be off. Use this cable to connect a Skylla-i to a VE.Bus BMS. The VE.Bus BMS will then disable the Skylla-i charger when the batteries are fully charged.
- Maximum input voltage: 70 V
- Minimum input voltage needed for switch on: approximately 6 V
- Switch off level: input voltage must be less than 1 V or must be free floating
Temperature sensor for BMV-702 & 712
This temperature sensor is suitable for the BMV-702, 712 & Smart Shunts
RS485 to USB interface
The Victron Energy RS485 to USB Interface allows you to connect the energy meter ET112 or ET340 to the Color Control GX. It is used for direct connection. There are two options available regarding the length of cable and you can choose any of them according to your requirements. It is available in 1.8m cable length and 5.0m cable length.
Temperature sensor VENUS/PMP/Quattro
Victron Energy temperature sensor for Venux GX, Phoenix MultiPlus and Quattro. It helps you in monitoring the temperature of your Victron Energy products. Quattro and Multiplus units are supplied with this temperature sensor. For Venux GX or if any the temperature sensor of your Phoenix MultiPlus and Quattro is damaged, you can order it now.
RS232 to USB converter
The Victron Energy RS232 to USB Interface allows you to connect the RS232 port of your Victron unit to a USB port of your computer for configuration and monitoring. All you need to do is connect RS232 connector to your Victron unit and USB connector to your computer and you are ready to configure and monitor the unit.
VE.Direct to USB interface
The VE.Direct to USB interface connects products with a VE.Direct connection to devices with a USB port, for example a computer. With this cable it is also possible to connect more than two VE.Direct products to a single CCGX.
VE.Direct to RS232 interface
The VE.Direct to RS232 interface allows you to connect your Victron products having VE.Direct connection to the device having RS232 port such as computer for monitoring and configuration. All you need to do is connect RS232 connector to your computer and VE.Direct connector to your Victron unit and you are ready to configure and monitor the unit.
MEGA Fuse
We have a wide range of MEGA fuse available with us. You can order any of these types according to your requirements. The options we have with us include 60A/32V, 80A/32V, 100A/32V, 125A/32V, 150A/32V, 175A/32V, 200A/32V, 225A/32V, 250A/32V, 300A/32V, 400A/32V, 500A/32V, 125A/58V for 48V products, 200A/58V for 48V products, 250A/58V for 48V products, and 300A/58V for 48V products. Whichever of these variants you want, book your order today and they will be delivered at your doorstep.
VE.Direct to BMV60xS Cable
VE.Direct to BMV60xS Cables are used to connect BMV-60xS to the Color Control GX for Battery monitoring. Victron Energy VE.Direct to BMV60xS Cable is available in two different sizes i.e. 1.5 m and 3 m.
Wall mount enclosure for BMV or MPPT Control
Features
- Enclosure for BMV or MPPT
- High-quality and reliable
- Durable and long lasting
Availability: Please call for Availability
Wall mount enclosure for 65 x 120 mm GX-panels
Features
- Enclosure for 65 x 120 mm GX panels
- High-quality and reliable
- Durable and long lasting
Availability: Please call for Availability
VE.Direct cable
A cable that is used to connect BMV-70x and low power MPPTs to the Color Control GX. Victron Energy VE.Direct Cable is available in different sizes including 0.3 m, 0.9 m, 1.8, 3 m, 5 m, and 10 m available in both straight and 90 degree angle models.
Phoenix Inverter Control VE.Direct
This panel is intended for remote on/off control of all the models of VE.Direct Phoenix inverter. It is simple, easy to operate, and user-friendly. It shows the status of inverter through the LED indicator.
Availability: Please call for Availability
VE.Direct non-inverting remote on-off cable
Use this cable to remotely control BlueSolar and SmartSolar MPPT charge controller models. However, it’s not necessary to use this cable on the larger SmartSolar models, as they feature an onboard Remote On/Off terminal. The charger will be enabled when the signal on the cable is high. The charger is disabled when the source signal is pulled low or left free floating.
Non-inverting remote on-off cable
The cable translates the remote on/off driver logic from the VE.Bus BMS (normally high, and opencircuit in case of alarm) to the logic needed by above products, active pull down to switch off.
Inverting remote on-off cable
The Inverting remote on-off cable is intended for products which require active pull down of the remote control terminal to switch on, while the source signal turns high when switch on is required.
Use this cable to connect the (discontinued) Phoenix Inverter 12/180, 24/180, 12/350 or 24/350 to a VE.Bus BMS or a BlueSolar MPPT Charger.
RJ45-splitter 1xRJ45 male/15cm cable/2xRJ45 female
This splitter is used to connect the MultiPlus 500VA – 1600VA range in parallel and 3 phase configurations, or in other installations where multiple VE.Bus ports are required. It includes 1 x RJ45 male connector, 15cm long cable and 2 x RJ45 female connector.
200A Insulated Busbars for DCS 200Ah Slim Lines
When stacking the DCS 200Ah batteries side by side these bus-bars provide a simple and perfect parallel solution.
Availability: In Stock
VE.Can to CAN-bus BMS
Use this cable to connect a CAN-bus enabled battery, not from Victron, to a Victron system. There are two types, A and B. See the manual for details on which cable to use for which brand of batteries.
MIDI-fuse
We have a wide range of MIDI fuse available with us. You can order any of these types according to your requirements. The options we have with us include 60A/32V, 80A/32V, 100A/32V, 150A/32V, 200A/32V, 30A/58V for 48V products, 40A/58V for 48V products ,50A/58V for 48V products, 60A/58V for 48V products, 80A/58V for 48V products, and 100A/58V for 48V products. Whichever of these variants you want, book your order today and they will be delivered at your doorstep.
You can also order fuse holder for MIDI fuse separately.
VE.Can RJ45 terminator
The VE.Can RJ45 terminator comes in a bag of two when ordered separately. The terminators are also included with some products, for example with the CANUSB. These are required for VE.Can networks. They are supplied with the Color GX.
ANL-Fuse
We have two variants of ANL fuse available with us. You can order any of these types according to your requirements. The options we have with us include 400A/80V for 48V products and 500A/80V for 48V products. Whichever of these variants you want, book your order today and they will be delivered at your doorstep.
You can also order fuse holder for ANL fuse separately.
VE. Net to VE. Bus Converter
The purpose of the VVC is to combine the powerful control of the VE Configure software, with the simple interface of the VE.Net Panel. With the VVC, you can configure the advanced features, and view status information of your VE.Bus device from a VE.Net Panel.
